80143001-TI-Rev A_VP8800.docx

Initial Release

2017 Nov 10

Presented by goofy.liu

10 Jan 2018 

VP8800 Key Loading SOP, based on PKI architecture.

-C01

22 Jun 2018 goofy.liu

• 1.[QC mode] support 2C-20 MSR Test , don't care key status.

FW Build: 25269 or later version.

RE VP8800 TS158 V1.01.001-C01 for MSR Test @ QC mode FW Build 25269.msg

-C02

22 Jun 2018 goofy.liu

• 1.Update Keys & Certificate Check method @ QC mode.

 Smart Check Injected Keys.

• 2.No MSR Test in QC mode.

This function will be supported 2C-20 cmd for MSR Test .

QC mode (Activated,Keys Installation) in next release w/ Firmware Build 25269.

-C01

13 Jun 2018 goofy.liu

• 1.Update Tamper Check Scenario, Remove Repower-On UUT

Using 90-02 w/o S/N --> Work in Tamper Test Scenario.

• 2.USB-HID test, + Repower-On UUT.
• 3.Perform S/N Injection after All Test Items.

-C03

08 Jun 2018 goofy.liu

• 1.[Exclusive in IDPP-1381,IDPP-1381D]

Update Tamper Repower-On Message to ask

user/operator to press [OK] after UUT beeps and being in Ready Status.

-C02

07 Jun 2018 goofy.liu

• 1.Fixed S/N input issue.

-C01

06 Jun 2018 goofy.liu

Approved in Build FW: 25252, Demo Version

• 1.Verified New MSR Format, w/ LRC

Test Card:

TRACK 1 = %TRACK17676760707077676760707077676760707077676760707077676760707077676760707?C

TRACK 2 = ;2121212121767676070707767676762121212?0

TRACK 3 = ;33333333337676760707077676763333333333767676070707767676333333333376767607070776767633333333337676760707?2

~~~~~~

Q-Card:

TRACK 1 = %0123456789012345678901234567890123456789012345678901234567890123456789012345?:

TRACK 2 = ;0123456789012345678901234567890123456?2

TRACK 3 = ;01234567890123456789012345678901234567890123456789012345678901234567890123456789012345678901234567890123?4

• 2.Isolated Secure Info Item @ QC mode
• 3.Isolated Customized Config Item @ Production + QC mode.
• 4.Rename exe file

old: TS158_PISCES_NoExt.exe

new: TS158_VP8800_NoExt.exe

• 5. P/N configuration Update for MSR Test at QC mode.

= MSR Test Available since Data Key Exists

= MSR Test N/A since No Data Key Exists

Production P/N             - MSR item at QC mode

------------------------------------------------------------

IDPP-1381                   -  MSR

IDPP-1581                   -  MSR

IDPP-1881                   -  MSR

IDPP-1881-U1               -  MSR

IDPP-1X81X                  -  MSR

Demo P/N             - MSR item at QC mode

------------------------------------------------------------

IDPP-1381D                  -  MSR

IDPP-1581D                  - MSR

IDPP-1881D                  -  MSR

-C04

03 May 2018 goofy.liu

• 1.Update Items for IDPP-1881-U1, Customer : United Air Line

a.Remove RS232 Item @ IDPP-1881-U1

b.Add United Cert Check "0F" @ IDPP-1881-U1, QC Mode

c.Remove Key Checks: PIN Key; DUKPT (Data) Key;

d.Remove MSR @ QC mode, since only LCL-KEK, w/o DUKPT & PIN

-C03

30 Mar 2018 goofy.liu

verified w/ FW build:25041~

1.Ethernet Ping - Add Netmask 255.255.255.0

2.Update P/N

Replace half size "-" with full size "-".

-C02

29 Mar 2018 goofy.liu

verified w/ FW build:25016

• 1.Production Mode, Device Reset

Add Device Reset in MSR; RFID; ICC

since Tamper Test might stay in Tamper Eanble status

(Generation CSR) to produce MSR Act Txn Error w/ returning sts 0x0A immediately.

• 2.Tamper Test:

Update Tamper Eanble / Disable Command Group

old: 04-21 + 01 / 04-21 + 03

new: 90-07;90-00;90-02 / 90-07;90-00

• 3.QC Mode, LCD Test.

Add LCD Cust Display Mode ON --> Show Default Image --> Cust Mode OFF

to display LCD Test Patterns.

• 4.Add UMFG-SN before Tamper Test. Copied from NEO 2.0 test plan.

• 5.P/N Update

  + IDPP-1881-U1, RS232 + USB-HID + Ethernet

-C01

23 Mar 2018 goofy.liu

verified w/ FW build:25016

• 1.+MSR, LEDs+Buzzer, and LCD Tests in QC mode.
• 2.Re-power UUT after Tamper Enable(90-02),

for Tamper-Battery test.

• 3.Secured Keys Check Rule in All P/Ns.

  They are LCL-KEK, DUKPT Key, and PIN Key.

• 4.P/N Check Rules Update

a) RS232

b) USB-HID

c) USB-HID+ ETH

d) RS232+ USB-HID+ ETH

• 5.Add Get Certs (81-0E) Info Check @ FW Info QC mode.
• 6.[Fixed] 2018 Feb 02, HW Tony's Report.

Wire 1 <--> 0 message displays reversed.

Printing out detail info when Engineer Mode w/ Debug "ON".

• 1.New Request - Tamper Enable, Lewis

RE Tamper verification for NEO 2 and VP8800 - TS improvement schedule..msg

• 2.SQA Report.msg

-C01

01 Feb 2018 goofy.liu

1.Date/Time Test : Time Zone Update

old = GMT/UTC + 08:00

new = GMT/UTC + 00:00

since NEO 2.0 Certificates Injection Tool

sets UTC +00:00 as standard time in the reader.

Old Time zone may cause Time Check Error in QC mode.

-C03

25 Jan 2018 goofy.liu

1.Tamper Item Update

 a.Add Tamper Enable / Disable Functions before and after "Get Tamper Status".

 b.Fixed Incorrect Tamper Info.

-C02

17 Jan 2018 goofy.liu

1.Remove Board Level Test Icon (BTM-XX..)

2.Add Delay 500m between MSR Test and RFID one.

  To provide more restoration time of 02-05 command

  after 1st time Erase Flash.

3.Update FW Info display message

  Old: "..TM4.."

  New: "NEO 2.0 / AR 3.0.0 +..."

4.Update Part Number List.

5.Verified @ FW V24089

-C01

12 Jan 2018  goofy.liu

V1.00.005-C01, 2018 Jan 11 Released

• 1.QC mode, PCI enable

  a-removed test items

    a.1-MSR test, KSN issue

  b-Tamper Test Update -

    Remove Tamper Enable while in QC mode

  c.USB-HID Test Update

• 2.MSR test item.

Legacy: 02-20 (Interface selectable, Non-secured)

New:    02-05 (Interface selectable, Secured/Non-secured compatible)

• 3.RTC, Data/Time Set commands

Legacy 25-05

New,UMFG mode, 90-07 --> 90-00 --> 90-01

• 4.Engineer Mode,

UMFG / SMFG Features Support

a.Load Certificates Support @ Engineer Mode

b.Load Keys Function Support @ Engineer Mode

c.QC Mode, item name update:

Legacy,Err "G53 MCD Chk" -->

Ok "G53 MCU Chk"

• 5.Part Number List Update

M IDPP-1X81 --> IDPP-1X81X

+ IDPP-1381.D  RS232 (115200), No USB-HID, No Ethernet

+ IDPP-1581.D, No RS232, USB-HID, No Ethernet, SRED

+ IDPP-1881.D, No RS232, USB-HID, Ethernet, SRED

-C01