Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

EconoScan CCD Barcode Scanner

Table of Contents

1. How do I connect the scanner to the host computer?

...

For a keyboard wedge interface (IDT4431-4) or USB/keyboard emulation interface (IDT4431-4U) scanner:

  1. Get into any simple text editor. Notepad is recommended in the Windows environment. (Locate it through Start/all programs/Accessories/Notepad)

  2. Scan a valid sample

...

  1. barcode (the EAN13+5 barcode on the bottom of Page 14 of the manual can be used as a sample test barcode). The scanner should beep once and the correct 13

...

  1. -digit output data should be displayed on the Notepad screen (see the notes below).

For a RS-232 serial interface scanner (IDT4421-4):

  1. Get into HyperTerminal in the Windows environment. (Locate it through Start/all programs/accessories/communications/HyperTerminal)

  2. Set up Hyper Terminal to communicate at 9600, none, 8, 1, Xon/Xoff through the COM port where the scanner is connected (Refer to General FAQ section for

...

  1. details on how to

...

  1. set HyperTerminal for testing)

  2. Scan a valid sample bar code. The scanner should beep once and the correct barcode data should be displayed in the Hyper Terminal Screen

Notes:

  1. Do not use the configuration bar codes in the manual as test bar codes. If you can't find a sample bar code with which to test the scanner, the EAN-13 +5 bar code located at the bottom of page 14 of the manual can be used as a test bar code.

  2. If the scanner does not beep, check the bar code label and verify that the bar code is a valid one.

  3. If the scanner beeps, but no data is shown in the text editor (Notepad) or HyperTerminal, check the scanner's interface setting. (Refer to Group 1 on page 9 of the manual for details.)

  4. If the scanner is verified as working, but it will not work with your application software, check the software requirement for the bar code scanner output data format. Re-configure the scanner accordingly.

3. My scanner is labeled as IDT4439U. How do I know what interface it is?

...

If the scanner has a 'Y' shaped cable, which has a PS/2 male connector on one end and a PS/2 female connector on the other end, it is a keyboard wedge interface unit (IDT4431-4). If the scanner has a 'Y' shaped cable on which one end is the DB9 female connector and on the other end is a circular power plug, it is an RS-232 serial interface unit (IDT4421-4). If the scanner is a single-ended cable with a flat USB connector on it, it is an a USB/Keyboard emulation unit (IDT4431-4U).

...

In GROUP 28 (on page 43 of the manual), scan the READ DIGIT NO SEND and CHECK DIGIT NO SEND bar codes.

6. How do I program the scanner to read the 13-digit bar code on the back of a book and output the ISBN

...

?

In GROUP 31 (on page 46 of the manual), scan the ISBN ON bar code.

...

In GROUP 11 (on page 19 of the manual), scan the NONE bar code under the TERMINATOR section.

10. How do I make the scanner do a TAB instead of an ENTER after a scan?

In GROUP 11 (on page 19 of the manual), scan the TAB bar code under the TERMINATOR section.

11. Why does the scanner read my 8-digit Code 128 bar code, but won't read a 4-digit Code 128 bar code?

The scanner's default minimum length for a Code 128 bar code is 5 characters. In order to To read a 4-digit bar code, you need to re-program the scanner so that the minimum length is equal or less than 4. Follow the instructions in GROUP 24 (on pages 37 & 38 of the manual).

...

In GROUP 21 (on page 33 of the manual), scan the Not Sent START/STOP bar code under the START/STOP section.

13. I have a keyboard wedge interface scanner (IDT4431-4), but I use it with a Laptop PC, which does not have an external keyboard. It scans once, and then will not scan anymore. What should I do?

 


Disconnect and reconnect the scanner to the laptop. In GROUP 1 (on page 9 of the manual), scan the NOTEBOOK bar code under the COMPUTER TYPE section.

Notes:

  1. This also applies to a desktop PC without a regular PS/2 keyboard connected (e.g. USB keyboard or no keyboard).

  2. A USB/Keyboard emulation reader is recommended for this kind of situation if the host is running Windows 2000/XP. You can simply replace the keyboard wedge cable with the USB interface cable (part number CAB601-1 for beige color or CAB601-8 for black color)

14. How do I program the scanner so that it outputs the data with a preamble and a postamble?

Follow the example Setting Procedure in Group 4 on page 12 of the manual.

15. I have

...

a USB/Keyboard EconoScan CCD scanner. Where do I find the driver?

The USB/Keyboard emulation reader uses the HID keyboard driver provided by the Windows Operating System. On a PC with Windows 2000 or XP, the driver will be installed automatically the first time the reader is connected to the USB port. The Windows 98 CD is required to locate and install the HID keyboard driver on a PC running Windows 98.

16. Which is the correct manual to download from the ID TECH website for the EconoScan CCD scanner?

It is the link User Manual under EconoScan CCD Scanner.

...

When generating a Code 39 bar code, you need to add a * character at the beginning and end of the data that you are encoding.

18. How do I make the Scanner output the barcode data and then

...

make the cursor

...

move down instead of

...

doing an Enter?

In GROUP 11 (on page 19 of the manual), scan the NONE bar code under the TERMINATOR section. Then in Group 4 (on page 12 of the manual), scan the 'Postamble' bar code, in Group 42 (on Page 58) scan the 'Down' barcode, go back to page 12, scan the 'Postamble' barcode again.

...

Yes; the cable's part number is CAB601-8 for the black color scanner and CAB601-1 for the beige color scanner.

20. How can the scanner read the bar code automatically without having to press the trigger button?

In Group 2, scan the "Continuous Mode" on top of page 10 of the User Manual to get it configured to keep the scan light on and ready to scan the bar code present to it.


21. How to reset the scanner to the factory default so it will output the original barcode data?

You can reset the scanner by scanning the 2 barcodes on Page 9 of the User Manual as indicated below.  And then test read a barcode in any text editor (e.g. Notepad) to verify the output.

...


See also:

Filter by label (Content by label)
showLabelsfalse
spacesKB
showSpacefalse
sortmodified
cqllabel in ( "versascan" , "econoscan" ) and space = "KB"
labelseconoscan versascan