24, Production./Assembly Test.
- RS232
- Ethernet

25. WiFi Rounter
SSID: IDTECH_Production
Pwd: 16964727

27. TestItemICCard.Board.Jig2
Board2. ICC In.. 6825\Board.xml
Card IN fig: TI_Item_023_Jig_ICC_Test
Pic Updated.

28. Pic Updated
TestItemLCD_TouchPanel_K81.Board.Jig2 
TestItemLCD_TouchPanel.Board.Jig2

29. Adding Keypad Timeout Waiting
20 secs timeout.
5 secs timeou ahead of key hit.

30.Adding RTC Set--> several items later --> Get/Check
+ TestItemSetTime.Board.Jig2
+ TestItemCheckTime.Board.Jig2

31.Jig2
+Touch LCD RT1052
+Touch LCD K81

====================
2021 Sept 16, goofy.liu
EVT2-2

Bitbucket: 7f542bed5df0f4a980547d2ca844760e741ec070

1.RFID.+remove CLT
V

2.TP Volt. - start secure task
V

3.jig2. install board  timeouts, +360000

4.move TP Volt 
RFID -->TP Volt 

5.board mode.Replace PN to Qisda Project Code

6.TP Volt. Remove Switch SIM2    command. No more SIM Toggle benefits. But TP voltage Values more corre

7.0.3a~0.8a,board jig1

8.shorten removal TP Check,  VCD_I

9.K81 Touch
+add picture.

10.SIM1 +SIM2 Switch Cmd.
+retrytimes 2,+interval 1000

11.TP Volt.
every tp check is iferror-continue flag.

12.PartNumber <--> Qisda Model Number Mapping
in PartNumber Selection Window

*13.Log File.
old : P/N+Date
new : P/N+Date+S/N|UID

14.SAM1~4, Jig1 Can't be very stable.
adding retrying mechanism.

15.Jig2 Test Model
Move RT1050 LED + Camera to the end.

16.Keypad Test Message
+ Beep Sound to confirm key has been done.
FormNote + FormExplain

17. Light Sensor
Jig 2 --> Jig 1.

18. TS namming , easy for Qisda Operator Identification.
TS194_VP8810 --> WHITESAND_TS194...
TS195_VP6825 --> OLYMPIC_TS195...
TS197_VP8810P --> BryceCanyon_TS197...

19. ICC Card, TestItemICCard
+ Card Insert Detection
+ Card Removal Detection

20.[Issue] ICC Test Card Seat PIN
Inserted ICC, Get Card Seat PIN: 0x02 --> Get ATR --> Get Card Seat PIN: 0x03 ? should be --> Removed Card, Get PIN:0x00.

21. ICC Test , Adding Card Seat PIN IN/OUT Check.

22.Adding WiFi/BT Check Method in Board Level Test - Jig1.

CFG = 2-3-5.BryceCanyon
 ==> JigEE_01_TestItemBoard_WiFiBT_Check

CFG = 1-4, WiFi+BT, BT Only
 ==> JigEE_01_TestItemBoard_BTOnly_SelfCheck

23.Board Level : Tamper Check
1.Ignore Battery
*2.Perform USB-Auto Disconnection Method.
3.Ignore Response of 90-02

24.Adding Tamper Test in Jig 2
+ Support Battery Check Ignored for Board Level Test.
   @ ProjectSettings.xml
   

2021 Sept 11, goofy.liu
EVT2-2 
Bitbucket: 2214f7486b425fa7372cbe6b2be764c06032e869

1.Production Test
  1.1 +,LTE Antenna Spectrum Tester : CMW 500
   1.1.A  North America
   1.1.B  EMEA , Asia.
   
  1.2 M,All input forms has automatically focus on, cursor on Pass/OK button.
  
  1.3 M,SerialNumber Injection Test
      Automatically Prefetch S/N if any and auto-selected S/N data after pop-up dialogbox.
   
  1.4 M, DeviceInfo Set Unify ID Input Box
      Automatically Prefetch ID if any and auto-selected it after pop-up dialogbox.
  
2.Board Level Test.
  2.1 Same as 1.2
  2.2 Same as 1.4

2021 Sept06, goofy.liu

EVT2-2

1.Fixed Issues.

 1.1 Tooltips Result Can't saved problem.